Dura Craft
 |
Ashley Mansions in Miniature Sale Price: $19.98  |
 |
DURACRAFT BACK PACK SMALL BURGUNDY Sale Price: $35.34 |
|
BACK PACK SMALL BURGUNDY Made with Cordura and fleece lining. |
 |
Dura-Craft Old Towne Miniature Village Duracraft Sale Price: $22.95 |
 |
DURACRAFT BACK PACK SMALL BURGUNDY Sale Price: $24.76 |
|
BACK PACK SMALL BURGUNDY Made with Cordura and fleece lining. |
 |
Grafix Clear Dura-Lar (Acetate Alternative) .005 20"x25' Roll Sale Price: $17.99 |
|
Roll 005 Clear Dura-Lar 20"x25' Dura Lar is an archival, non tearing, non yellowing polyester film. |
 |
Glassines For Strip of 4 - 2-1/4 (1000 Pack) |
|
Glassine sleeves have been a favorite storage medium for photo professionals for packaging, handling and storage of negatives and photos. The translucent envelopes are made of archival, acid-free pH negative non-plasticized paper... |
 |
5 ML Clear Duralar 40 inches wide x 12 feet Sale Price: $18.95 |
|
Clear Duralar...Duralar is a clear lightweight polyester sheeting. It is neutral pH and ideal for protecting artwork. Polyester is much more flexible than acetate and a much better choice when protecting artwork drawings or maps when folding and taping the plastic to the back of the work... |
 |
Duracraft Replacement Tank DWM-250-TANK |
|
Replacement Tank (without cap) for Duracraft DWM-250, DH-910, Honeywell HWM-910, and ReliOn RWM-975(old style, not new) Humidifiers |
 |
A Second Treasury of Knitting Patterns Sale Price: $25.50 |
 |
10' x 10' Commercial E-Z UP Instant shelter with 4 zippered sides Sale Price: $161.00 |
|
10 feet length x 10 feet width instant shelter, Sets up in seconds , Fold up 5 ft. long - fits in most trunks , Ideal for commercial or recreational use (small business, craft shows, tailgate parties, picnics, camping, outdoor sporting events) ... |
How to safely remove paint from an aluminum Boat.?
Not sure if I should sand it, I would not think so. Is there a stripper I can buy that won't eat the aluminum? I was also thinking of getting the inside of the aluminum boat sprayed with truck bedliner, white in color of course. Would this be a bad Idea? The boat is and old Dura-Craft 14 ft V-hull made of aluminum. Thanks for your time and concern with this question.
Soda or dry ice blasting is very safe on the alloy, very effective and gives the best possible start for an A1 paint job - but it is not cheap.
There are plenty of strippers that will have no effect on the alloy, although if you have a two pack finish you will find they are much tougher to attack chemically. If you have a two pack finish in fair order you are best off getting any repairs done, lightly sanding, using an etch primer on any raw alloy, using a high build epoxy primer over the lot and then a couple of coats of two pack for a long term fix. These products require a professional attitude and safety gear to be used at all times.
Bedliner in an alloy boat can look o.k. and seems cost effective - but corrosion can occur underneath it that requires a lot of work later to try and fix. Adhesion to alloy is difficult without correct etching and priming, and once you have done that you may as well finish the job properly. A similar preparation and treatment as the outside of the hull will give a much longer term fix. Here's a trade tip - use sugar liberally on the last coat inside for grip with two pack. Hose the surface down when fully cured to dissolve the sugar and leave a very effective but soft on the clothes and knees grip pattern. The grade of sugar makes the grip fine or course.
Good luck.
Duracraft (Fisher Price) deskfan 7''
« Vinyl Baby | Home | Rolling Pin American »
Leave a Comment